Concrete cutting in Stamford CT - clean openings, cut after the slab is scanned
Need a doorway, a trench for a drain or a hole for a pipe? We scan, mark and cut it clean.
What does concrete cutting involve at your house?
Concrete cutting in Stamford, CT means sawing or drilling clean openings, trench lines and round holes in slabs and walls, so a drain, a doorway or a new section of concrete can go in without wrecking the rest.
Usually something has to get through concrete. It might be a drain line under a basement floor, a doorway in a foundation wall, or a cracked piece of driveway that has to come out before the new one goes in. A jackhammer gets there too, but it tends to crack the parts you meant to keep.
The price moves with how deep the cut runs, how much steel is inside, whether it's a wall or a slab, how easy the spot is to reach and whether we haul the pieces away. The schedule turns on the scan and on what the city wants before we start, and your written estimate spells out what's included.
- Flat saws cut slabs like driveways, patios and garage floors for trenches, removals and straight lines.
- Wall saws ride on a track to cut doorways, windows and other openings in foundation walls.
- Core drilling makes round holes through slabs and walls for pipes, drains and electrical conduit.
What happens when you call us about cutting concrete?
I've run this business since 2017, we're licensed and fully insured, and I still come out to every job myself. Here's how a cutting job runs from your call to the cleanup.
Send us the details
Call (475) 333-3026, use the form or email contact@concretestamford.com with where the cut goes, what it's cutting through, the rough size and a few photos. That way I show up knowing whether it's a slab, a wall or a hole for a pipe.
I walk and measure the site
I come out myself, measure, check what sits above and below the cut and ask what the opening needs to do. You get a written estimate that spells out the prep, the cuts and everything that's included.
We check permits, set the date
Once you say go, we check with your city's building office, and if the cut reaches the street, Stamford's Engineering Department has its own street opening and street use permits. In Connecticut, any digging with power equipment needs a call to the state's clearinghouse at least two full business days ahead, so that sets the earliest start.
We scan, cut and clean up
My crew does the cutting, and I'm on site for the steps that matter most, starting with the scan and the layout. When we leave, the edges are clean and the pieces are either hauled off or left where your estimate said.
Saw cuts, core holes and wall openings in concrete
These photos show the kind of cutting the trade does, from straight slab cuts to round core holes. Tap any picture for a closer look at the edges and the setup.
Textured concrete pool deck surrounding a swimming pool, with patio steps and a covered seating area.
Curved stone-block retaining wall with a broad cap, surrounding a paved garden seating area with planters.
Wooden outdoor deck steps rise to a house patio beside a hot tub, seating area, and black railings.
Concrete driveway with light gray slabs and red brick borders, beside a parked golf cart and landscaped yard.
Covered patio with a dark stamped-concrete floor beside a smooth concrete slab, garden, and wooden fence at sunset.
Stamped concrete patio with a dining set, dark red border, and steps up to a brick house.
Get a written estimate for your concrete cutting job
We reply within one business day to set a time, and I come out to measure and send a free written estimate. There's no pressure to book, and photos of the spot help.
(475) 333-3026Questions people ask about cutting concrete
These are the questions I hear most before anyone picks up a saw. If yours isn't here, ask it at the estimate and I'll give you a straight answer.
How much does concrete cutting cost in Stamford, CT?
Concrete saw cutting across the US usually costs about $4 to $25 per linear foot, and that covers the sawing, not breaking out or hauling the pieces. Reinforced or deeper slabs cost more per foot, wall sawing can run higher still, and on a small job a cutter's minimum or setup charge can outweigh the per-foot rate. Your written estimate shows what goes into your number.
Do I need an engineer to cut a doorway in a concrete foundation wall?
One concrete cutting guide says yes, and advises having the lintel, the beam that carries the wall over the opening, sized by an engineer unless the building department explicitly accepts a pre-engineered one. That's because the load above shifts onto the wall left at the corners of the opening. We ask your city's building office what it will accept before we cut.
Why should a concrete slab be scanned before cutting?
A scanning company advises a professional scan before any cutting or coring, because drawings and what you can see on the surface aren't enough to show an area is clear. Connecticut's call-before-you-dig records can also leave out lines you own that serve only your house. A radar scan has its limits too, since rebar and cables packed close together can blur together on the screen.
Can concrete be cut indoors safely?
Yes, with the right saw and enough air. A sawing trade group's guideline calls for ventilation that meets OSHA standards when fuel-burning saws cut inside, and electric, hydraulic or pneumatic saws are other options, so ask us which one suits your basement or garage.
How do I keep dust down when concrete gets cut at my house?
Most flat, wall and wire sawing runs wet, because water cools the blade and turns the cuttings into a slurry instead of a cloud of dust. That runoff has to be vacuumed or contained, so ask how the crew plans to handle it before the saw starts.
What is the best way to cut thick or heavily reinforced concrete?
Wire saws are the usual choice for thick or heavily reinforced sections, and hand saws handle tight spaces and smaller openings. I'll tell you at the walk-through which one your job calls for, since a lot of steel also pushes the price up.
Concrete cutting in Stamford and nearby cities
Stamford's Building Department lists renovation and demolishing but not concrete cutting, so we ask the city what your job needs and handle any permit with you. We do the same work in the cities around it, in Connecticut and Westchester.